darkhawk22
New Member
Great work Pat, the satin red is sharp! Also, nice touch with the fuel shut off knob!
Sportsman 200 on Steroids
- Thread starter sportscarpat
- Start date
chainmaker
Well-Known Member
Exceptional work Pat!!
Lurker
New Member
Nice job Pat, this is your most beautiful bike yet. I love the color and finish. I also like that you used a vintage style pedal on this build. It's the small details that really make it look authentic and finish it off.
Did you use the same counter shaft sprocket setup on this bike that you have used on previous builds of did you design another version of it?
Did you use the same counter shaft sprocket setup on this bike that you have used on previous builds of did you design another version of it?
culvercityclassic
Well-Known Member
That is a great build Pat, you are always a 1/4 mile ahead of me... Not sure if I can catch ya...
What's the plan for this bike? What speed are you looking at? That cc of a motor, I have my speculations to what was built but will keep my mouth shut. You sure have a good guy by your side for motor work (Agk)
What's the plan for this bike? What speed are you looking at? That cc of a motor, I have my speculations to what was built but will keep my mouth shut. You sure have a good guy by your side for motor work (Agk)
sportscarpat
Bonneville Bomber the Salt Flat record breaker
Hi Lurker,
When I figured out all my offsets it looked as though my standard reduction drive would be fine. I drew up the tires when they were not fully inflated. Thought they were 3" wide and turned out to be just over 3 1/4". I went ahead and made some slight adjustments. Required a thicker adapter plate for the rear sprocket. Front reduction unit was the real challenge to narrow up, but I was able to make it all work.
sportscarpat
Bonneville Bomber the Salt Flat record breaker
1/4 mile ahead of you? Yeah, right. I thought the Morini was the best engine going till I saw you running your first clone engine. A week later I had one sitting in my shop trying to figure out how to make it work. Initial plans are to see how fast she will go. My last bike could push 60 mph on Simplex tires. Now that I have H rated motorcycle rubber I guess I'll see how tall of a gear I can push. If I can push a 40t rear sprocket it should do over 80 mph. It will be interesting to see if it will still pull away from the line smoothly. I'll keep you guys posted!
chainmaker
Well-Known Member
What do you think Pat? Will you be taking the bike?
cobrafreak
New Member
I have no where near the engine mods as Pat does. With my 200cc I have the 22mm Mikuni, stiffer valve springs, racing flywheel, and the better connecting rod. No porting, no cam, probably restrictive exhaust. I can do 53mph on the flat with Pats 44tooth rear sprocket. With more power, lighter bike, and more aero seating arrangement I would be surprised if Pat couldn't hit upper 70's, lower 80's. Be sure to get video!
sportscarpat
Bonneville Bomber the Salt Flat record breaker
We did some pretty serious testing today. Leaving the front primary gearing alone and working with the split rear sprocket system we had the following results:
48t rear sprocket at 71 mph
44t rear sprocket at 76 mph
40t rear sprocket at 68-75 mph
It would appear that the 40t in the rear is just a little too tall to push. The 44t seams to be the best balance. All speeds were measured with a properly calibrated digital speedometer mounted on the bike and a chase vehicle so these are accurate numbers. Bike was rock solid stable at these speeds, too. Speeds were also not just momentary numbers. I held it at 75 mph for at least two solid miles before I let off. It's a big claim but I think I now own the worlds fastest motorized bicycle!
Bonneville Flyer by Sportsman Flyer, on Flickr
48t rear sprocket at 71 mph
44t rear sprocket at 76 mph
40t rear sprocket at 68-75 mph
It would appear that the 40t in the rear is just a little too tall to push. The 44t seams to be the best balance. All speeds were measured with a properly calibrated digital speedometer mounted on the bike and a chase vehicle so these are accurate numbers. Bike was rock solid stable at these speeds, too. Speeds were also not just momentary numbers. I held it at 75 mph for at least two solid miles before I let off. It's a big claim but I think I now own the worlds fastest motorized bicycle!
Bonneville Flyer by Sportsman Flyer, on Flickr
harry76
Well-Known Member
WHOA!!!!!!!! That thing is bad. I love this bike. One thing though, the bike is perfect and far beyond anything i could ever build but to my eye, one small thing that looks odd to me is the silver secondary chain guard. I dig the silver primary chain guard but feel your bike would be that little bit nicer if the secondary was red. Just a small criticism, just thought id share my $0.02.
Either way one of the nicest bikes ever built here, and definitely the fastest.
Just wondering what the centrifugal clutch that you use? Ive CCC use the same clutch.
Either way one of the nicest bikes ever built here, and definitely the fastest.
Just wondering what the centrifugal clutch that you use? Ive CCC use the same clutch.
cobrafreak
New Member
I use your 44t rear sprocket also and I am glad I got that size. Congratulations on the successful speed test!
chainmaker
Well-Known Member
Very Cool Pat !!!!! I hope there is some video.
motorhedfred
Member
How did the brakes do hauling you down from those speeds Pat ?
Crazy Horse
Dealer
Harry, see this link below. If I'm understanding your question correctly, you are asking Pat what type of clutch he's using?
Pat, has custom designed his own ECCENTRIC'S aka reduction drive / Pedal Gear Crank system, that is similar to those used on Early Teen's motorcycles.
I have copies of the Original 1914 Patents showing Mr. Harleys design, yes from The Harley-Davidson Motorcycle Co.!
The below post is from Pat's thread:
Whizzer Powered BTR, it's post #24, where Pat describes his engine reduction pedal drive system.
Pat's, design is inspired by Early Teen's motorbikes aka motorcycles.
Awesome work Pat!
Peace C.H.
See below Link to Pat's thread: Whizzer Powered BTR.
http://motorbicycling.com/showpost.php?p=245558&postcount=24
SISH! 76 MPH fur cry'n out loud...cobrafreak
New Member
So when is there going to be a Bonniville Flyer backpack parachute system made available for purchase? 
Robertriley
New Member
Pat,
Can we get a nice shot of the wheels and tires. Going with motorcycle wheels was a great idea.
Can we get a nice shot of the wheels and tires. Going with motorcycle wheels was a great idea.
sportscarpat
Bonneville Bomber the Salt Flat record breaker
My brother Rich get's credit for pushing us in the direction of motorcycle tires. It's nice not to worry about a tire exploding at speed, and 76 mph on H rated rubber is nothing to worry about. Rims are custom drilled for our spoke selection. Hubs have a fair amount of custom parts as well with upgraded axles, backing plates and spacers. Here are a couple pictures.
Bonneville Flyer by Sportsman Flyer, on Flickr
Bonneville Flyer by Sportsman Flyer, on Flickr
Last edited: