Media added by bishop letov

GoldenMotor.com

Navigation

  1. Example Category 137
Browse albums

Most media items

  1. allen standley
    81

    allen standley

  2. John Newkirk
    46

    John Newkirk

  3. Mark Murphy
    36

    Mark Murphy

  4. Tyler6357
    36

    Tyler6357

  5. W
    29

    Weedge1212

Media statistics

Categories
1
Albums
1,888
Uploaded media
9,677
Embedded media
17
Comments
1,006
Disk usage
1.5 GB
The Laminator composit panel I was using to tie the rack to the rear tire forks had broken going over some really rough terrain..( its just aluminum s

The Laminator composit panel I was using to tie the rack to the rear tire forks had broken going over some really rough terrain..( its just aluminum s

  • 0
  • 0
Had to add this conduit clamp due to the old way I had it bolted together, would pop out of the original bracket on the wacker shaft and start to ch

Had to add this conduit clamp due to the old way I had it bolted together, would pop out of the original bracket on the wacker shaft and start to ch

  • 0
  • 0
Milage that the speedo is showing minus the 40 miles prior that I had on the odometer because I reset it to see how much fuel milage i was getting to

Milage that the speedo is showing minus the 40 miles prior that I had on the odometer because I reset it to see how much fuel milage i was getting to

  • 0
  • 0
opposite side where there is no wear for comparison

opposite side where there is no wear for comparison

  • 0
  • 0
wear on tire alone

wear on tire alone

  • 0
  • 0
Wear on roller and tire

Wear on roller and tire

  • 0
  • 0
top of fender to fork brace. No it isnt lopesided. My wheel has a caliper and disc up front so the tire is offset to the right a little.

top of fender to fork brace. No it isnt lopesided. My wheel has a caliper and disc up front so the tire is offset to the right a little.

  • 0
  • 0
another full pic of how the fender stay is fashioned and mounted

another full pic of how the fender stay is fashioned and mounted

  • 0
  • 0
10 Guage round wire stock fender stays that are wire tied to the fork and held at the bottom with washers.

10 Guage round wire stock fender stays that are wire tied to the fork and held at the bottom with washers.

  • 0
  • 0
Didnt like the bracket that came with the mirror and left the mirror too inbound. I used a conduit clamp here that usually attaches to electrical stru

Didnt like the bracket that came with the mirror and left the mirror too inbound. I used a conduit clamp here that usually attaches to electrical stru

  • 0
  • 0
My cooler rack pan that allows my cooler (aka trunk aka water proof carryall) to my rack platform. Does move around and only takes one bungy to hold

My cooler rack pan that allows my cooler (aka trunk aka water proof carryall) to my rack platform. Does move around and only takes one bungy to hold

  • 0
  • 0
Detail of how I adapted the stock throttle lever to work with the brake cable off the schwinn. I hack sawed all of the other bits off the throttle lev

Detail of how I adapted the stock throttle lever to work with the brake cable off the schwinn. I hack sawed all of the other bits off the throttle lev

  • 0
  • 0
Scavenged Adjuster and Brake cable outer casing from the Schwinn.

Scavenged Adjuster and Brake cable outer casing from the Schwinn.

  • 0
  • 0
Scavenged throttle shifter from a 79 schwinn i picked up for 5 bucks and saved it from the scrap heap. Modified by drilling out the ratchet lever so i

Scavenged throttle shifter from a 79 schwinn i picked up for 5 bucks and saved it from the scrap heap. Modified by drilling out the ratchet lever so i

  • 0
  • 0
Showing the Kill switch mounting and position. I used the throttle housing from the weed wacker to mount it under my seat post. soon itll house anther

Showing the Kill switch mounting and position. I used the throttle housing from the weed wacker to mount it under my seat post. soon itll house anther

  • 0
  • 0
just another shot to show the clearance for the rear brakes and the pivot stay.

just another shot to show the clearance for the rear brakes and the pivot stay.

  • 0
  • 0
Fender / rear rack pivot brace attached to the platform of the Rear Rack and to the Crossmember that would be used for the old style brakes

Fender / rear rack pivot brace attached to the platform of the Rear Rack and to the Crossmember that would be used for the old style brakes

  • 0
  • 0
Used flat struts here in the front and it gives me the extra clearance I need for peddliing and a place to attach tie downs effectively

Used flat struts here in the front and it gives me the extra clearance I need for peddliing and a place to attach tie downs effectively

  • 0
  • 0
Platform and where the uprights come together

Platform and where the uprights come together

  • 0
  • 0
Mounting of the struts to the rear axle

Mounting of the struts to the rear axle

  • 0
  • 0
good side view of the rear rack made from electrical struts used to hold conduit on the wall for wires.

good side view of the rear rack made from electrical struts used to hold conduit on the wall for wires.

  • 0
  • 0
front of fender

front of fender

  • 0
  • 0
rear of fender

rear of fender

  • 0
  • 0
fender from side albeit upside down.. (:<

fender from side albeit upside down.. (:<

  • 0
  • 0
Top Bottom