jbcruisin
Active Member
Here's some pics.
48? Whizzer barn find project
- Thread starter SlowBalt
- Start date
jbcruisin
Active Member
Do you need a fuel sediment bowl? Here's one cheap:
http://www.ebay.com/itm/SEDIMENT-BO...123?pt=LH_DefaultDomain_0&hash=item4d0e449f9b
http://www.ebay.com/itm/SEDIMENT-BO...123?pt=LH_DefaultDomain_0&hash=item4d0e449f9b
Last edited:
SlowBalt
Member
I think I only need the spring. Is it a very strong spring or could I just grab a spring from the hardware store?
Last edited:
SlowBalt
Member
Thanks for all the help Jay.
Just for the **** of it I went to the hardware store today and it turns out they had a spring for $2.
Now all I need is a gas cap ,controls ,cables ,tires ,tubes fender struts and a drive belt.
Unfortunately it will be a few weeks before I have the cash to get her going.
Just for the **** of it I went to the hardware store today and it turns out they had a spring for $2.
Now all I need is a gas cap ,controls ,cables ,tires ,tubes fender struts and a drive belt.
Unfortunately it will be a few weeks before I have the cash to get her going.
MEASURE TWICE
Well-Known Member
I like this! Say, the engine in that foam, was it just the old one from the barn find or did you get another from somewhere?
MT
PS, I was looking at some thread that you had a picture in August 2012 and looked like the same engine. You had it on deck for a while?
Your other thread:
http://motorbicycling.com/showthread.php?t=41331 Page #1 Post #6
Rat Rods I end up with for just my trying to get by with fabricating without all proper stuff
Still there are people that marvel. Some words like cool ect... but this one little girl said I should get the Nobel Prize... ha, if I did I could afford all the tools and a shop!
MT
PS, I was looking at some thread that you had a picture in August 2012 and looked like the same engine. You had it on deck for a while?
Your other thread:
http://motorbicycling.com/showthread.php?t=41331 Page #1 Post #6
Rat Rods I end up with for just my trying to get by with fabricating without all proper stuff
Still there are people that marvel. Some words like cool ect... but this one little girl said I should get the Nobel Prize... ha, if I did I could afford all the tools and a shop!
Last edited:
SlowBalt
Member
It is the original . I had Quinton rebuild it last year. I've had the bike since last year.
jbcruisin
Active Member
AX62 A place that sells industrial belts would have them.
chainmaker
Well-Known Member
You can get them at most auto parts stores as well.
SlowBalt
Member
Tires came in today.
I went with the closest match to the Goodyear tires that were on the bike when I got it. The belt ,gas cap and fender struts also came in. Unfortunately the struts fit perfect in the rear, but are 1 inch to short in the front . So I will have to weld in an extension.
Unfortunately progress will slow for a wile. It's only12 outside in the shed and my space heater can't even come close to keeping it workable out their now. Also I am being transferred to the night shift at work 8pm to 8am. So that will take a while to get use to . But I vow to have it running by spring.
I went with the closest match to the Goodyear tires that were on the bike when I got it. The belt ,gas cap and fender struts also came in. Unfortunately the struts fit perfect in the rear, but are 1 inch to short in the front . So I will have to weld in an extension.
Unfortunately progress will slow for a wile. It's only12 outside in the shed and my space heater can't even come close to keeping it workable out their now. Also I am being transferred to the night shift at work 8pm to 8am. So that will take a while to get use to . But I vow to have it running by spring.
Last edited: