Rust Removal

fundreamer1 · Jan 19, 2011

I used a mixture of 50% White Vinegar and 50% lemon juice to remove the rust from my parts and this is without me scrubbing or even wiping the parts down at all!
The peddle crank was only treated on half, while the other side was not. The kickstand was only partially treated as well.

bairdco · Jan 19, 2011

looks good...

7-up works really good, too.

fundreamer1 · Jan 19, 2011

bairdco said:
looks good...

7-up works really good, too.

LOL! I'm sure it does, but the lemon juice don't make the parts sticky!

Goat Herder · Jan 19, 2011

I am as impatient as all get go sometimes. I use muriatic acid. Very dangerous stuff and not to be taken lightly ether ! It can eat through your skin down to the bone! Cleans up metal right and thorough quick I tell yeah .

Muriatic Acid Rust Removal

Muriatic Acid Rust Removal | eHow.com

I get the stuff at the hardware store. Used this stuff to strip the firewalls of rust etc on old cars. Suggest reading up on this stuff before using it tho.

fundreamer1 · Jan 19, 2011

Goat Herder said:
I am as impatient as all get go sometimes. I use muriatic acid. Very dangerous stuff and not to be taken lightly ether ! It can eat through your skin down to the bone! Cleans up metal right and thorough quick I tell yeah .

Muriatic Acid Rust Removal

Muriatic Acid Rust Removal | eHow.com

I get the stuff at the hardware store. Used this stuff to strip the firewalls of rust etc on old cars. Suggest reading up on this stuff before using it tho.

This stuff I use is not dangerous, after using you can pour it out on the ground. I also run water on it after wards as it smells, but it is biodegradable. I think I will leave the muriatic acid alone, (nasty stuff!)

Goat Herder · Jan 19, 2011

Its biodegradable too

fundreamer1 · Jan 19, 2011

Goat Herder said:
Its biodegradable too

Since it will eat through skin to the bone, I don't think I want to test that out on my lawn.

Goat Herder · Jan 19, 2011

An oldie but goodie trick is to use this stuff to clear out clogged plumbing. I have plastic pipe to my plumbing on the house so once in a while [blue moon]I will use it to make a drain drain more better.

It is said that the stuff is bad on old still pipes [plumbing] I always got away with it tho. After the clog went away which happens usually immediately I would thoroughly rinse out the pipes.

I still see rust on them parts

I here you tho

Can I Use Muriatic Acid to Unclog a Drain? | eHow.com
Good stuff

Hydrochloric acid - Wikipedia, the free encyclopedia

Can be diluted too just add water.

fundreamer1 · Jan 19, 2011

Goat Herder said:
I still see rust on them parts I here you tho

If you go back and read my description, you will that I said that I only dipped part of the peddle crank in the solution, that part has no rust on it. The part that was not dipped was so you could see the difference it made. (^)

Goat Herder · Jan 19, 2011

I miss interpreted that I see it now ''sorry''. For a sec I thought it was not working to its potential. Looks very good actually!!! Carry on....

yodar · Jan 19, 2011

Goat Herder said:
I am as impatient as all get go sometimes. I use muriatic acid. Very dangerous stuff and not to be taken lightly ether ! It can eat through your skin down to the bone! Cleans up metal right and thorough quick I tell yeah .

Muriatic Acid Rust Removal

Muriatic Acid Rust Removal | eHow.com

I get the stuff at the hardware store. Used this stuff to strip the firewalls of rust etc on old cars. Suggest reading up on this stuff before using it tho.

Pickling a part in Muiratic is important first step prior to plating with copper, then Nickel or chrome

HOWEVER! iT CAN BE DONE ELECTRONICALLY.GOOGLE "electrolytic rust removal:

POUR A TEASPOONFUL OF BAKING SODA (OR WASHING SODA)IN A STURDY PLASTIC OR GLASS VESSEL.

1. Hook the negative 12V to the rusty part and

2. HOOK the positive to a steel bolt or a piece of steel chain immersed in the bath, making sure all is immersed.

The electrolytic process will plate out all your rustto the steel bolt/CHAIN anode.

I used a 12V DC CB power supply but a car battery will work too, even lantern batteries.

YODAR

Goat Herder · Jan 19, 2011

Sounds interesting. I might try it some time Yodar

Venice Motor Bikes · Jan 19, 2011

I use a small brass bristle wire wheel in a drill motor. (^)

joabthebugman · Jan 19, 2011

My BIL uses the electrolysis method for cleaning old antique cast iron pots that he sells on e=bay

I have seen him take a decrepit $2 piece of rust and turn it into a new looking $100 kettle in a matter of hours
I have seen Yodar take a rusted shut pair of pliers and turn them into a usable tool

He uses a 55 gallon garbage can and liquid pool PH hooked up to a car battery charger

The by product is pure hydrogen, so smoking is a big no no

wayne z · Jan 20, 2011

Rusty chrome cleans up great with a small stainless steel brush. Stainless is softer than chrome, so it's kinda hard to scratch chrome with one.
Realy rusty places on chrome can be touched up with alumunum paint,the results makes the spot hardly noticable.

This bike was very rusty before I started the build.

GearNut · Jan 20, 2011

I have used both the lemon juice & vinegar and the battery charger method for years now.
Which method I choose depends on the size of the item to be cleaned and the amount of rust to be destroyed...umm...removed.

Both work awesome and both result is a nasty looking solutions that you can dump on the ground with no fear of polluting the environment. They are all natural and biodegradable.

I soak parts in the lemon-vinegar for a day or two. Same with the battery charger method.
A useful tip to help prevent overloading a battery charger: Incorporate about 10 feet of steel rebar wire or utility wire in series with the electrical circuit. It will put about a 3 amp load on the charger to prevent it from thinking there is a dead short and tripping the internal safety circuit breaker. The steel wire will get warm to the touch, but no where near hot. By the way, steel wire is a poor conductor of electricity and that's why it works so well in this application.

fundreamer1 · Jan 23, 2011

This is all great information from people that have been there and done that. I was wondering if there might be any other ideas or methods that anyone knows of or tried and tell of the results.
This is one of the important steps when dealing with an older bike and when people can show pics (like before and after) that would be great as well. What do you think is the better methods and why?
Just wondering.

yodar · Jan 23, 2011

fundreamer1 said:
This is all great information from people that have been there and done that. I was wondering if there might be any other ideas or methods that anyone knows of or tried and tell of the results.
This is one of the important steps when dealing with an older bike and when people can show pics (like before and after) that would be great as well. What do you think is the better methods and why?
Just wondering.

As a B.A.T.F.-Licensed C & R firearms collector, I don't have a long skinny vessel to electrolytically de-rust an ancient Mauser, so I squirt some Ballistol onto the piece. letter set overnight, then next day I go over it with 0000 steel wool. Then I solvent de-grease it with naptha so the piece can be re-blued or restored.

Ballsitol is an excellent penetrant, rust preventative and has been a staple in the Werhmacht since 1898. Krauts even used Ballsitol as an antiseptic for minor scrapes and some people took it internally. the stuff smells NASTY! but it works on rust, wood, restores old leather. VERY popular in the trade.

yodarDREADFUL!

fundreamer1 · Jan 23, 2011

yodar said:
As a B.A.T.F.-Licensed C & R firearms collector, I don't have a long skinny vessel to electrolytically de-rust an ancient Mauser, so I squirt some Ballistol onto the piece. letter set overnight, then next day I go over it with 0000 steel wool. Then I solvent de-grease it with naptha so the piece can be re-blued or restored.

Ballsitol is an excellent penetrant, rust preventative and has been a staple in the Werhmacht since 1898. Krauts even used Ballsitol as an antiseptic for minor scrapes and some people took it internally. the stuff smells NASTY! but it works on rust, wood, restores old leather. VERY popular in the trade.

yodarDREADFUL!

So how do you think it would do to help remove rust from old bicycle parts, and how much does it cost?

yodar · Jan 23, 2011

fundreamer1 said:
So how do you think it would do to help remove rust from old bicycle parts, and how much does it cost?

Using Ballsitol and 4-ought is easier removing rust on a bike than on a blued firrearm

just time and elbow grease ballistol - The World's Most Use-ful & Environmentally Friendly Lubricant ten bux UP at gun shows

website ordering ain't cheap,fergeddabbouddit!

Rust Removal

New Member

a guy who makes cool bikes

New Member

Gutter Rider

New Member

Gutter Rider

New Member

Gutter Rider

New Member

Gutter Rider

New Member

Gutter Rider

Custom Builder / Dealer/Los Angeles

New Member

Active Member

Active Member

New Member

New Member

New Member

New Member