Recent Activity

Activity stream for all registered members at Motorized Bicycle Engine Kit Forum.

  1. msrfan liked Gbrebes's post in the thread My Bike in an Article.

    Good Evening Everyone, My bike made it into an online motorcycle article. The “magazine” is called Rideapart, and the link is...

    Oct 16, 2017 at 11:54 PM
  2. curtisfox replied to the thread briggs & Stratton 3hp 80300 MODEL HELP..

    No matter how good a clutch it will burn, pulling to hard. Jack shaft is needed. Burn, Burn, Burn ring of fire

    Oct 16, 2017 at 11:08 PM
  3. msrfan replied to the thread Plastic camshafts?.

    The cam turning half the crank speed would probably hold up. They have a compression release that takes up quite a bit of room. Depends...

    Oct 16, 2017 at 10:54 PM
  4. TheSignGuy replied to the thread briggs & Stratton 3hp 80300 MODEL HELP..

    Oh trust me I'm reading up on clutches as we speak... Do those options or buy a fancy clutch which will give me full control it's...

    Oct 16, 2017 at 10:44 PM
  5. curtisfox replied to the thread briggs & Stratton 3hp 80300 MODEL HELP..

    Do 24" wheels, do both wont look so bad. Price of one clutch you could get a jack shaft. Measure twice did a artificial on fixing...

    Oct 16, 2017 at 10:39 PM
  6. malatious replied to the thread Nel Lusso 4-Stroke Huashengtai Motorized Bike.

    I have one bike built with a Huffy and the Huasheng 4 stroke motor. It turned out nice. Make sure you completely disassemble the bike...

    Oct 16, 2017 at 10:28 PM
  7. ZipTie replied to the thread New to the forum, first build..

    It is 1.5 dia hub on the Nel Lusso rims I have here. Your hub should be the same. FYI, They work well with a 1.5 Cnc hub adapter also. I...

    Oct 16, 2017 at 10:12 PM
  8. ZipTie replied to the thread New and excited.

    PS, Oh yeah the fat tire trike sounds cool as heck, just a bit more challenging on a trike for gas power. If you have the skill go for...

    Oct 16, 2017 at 9:58 PM
  9. TheSignGuy replied to the thread briggs & Stratton 3hp 80300 MODEL HELP..

    Which is most direct "yes you tell me can't avoid using jackshafts." Looking for an instant drop on solution even if I have to drop...

    Oct 16, 2017 at 9:50 PM
  10. curtisfox replied to the thread New and excited.

    This guy is attempting to, LOL https://motorbicycling.com/threads/briggs-stratton-3hp-80300-model-help.63489/#post-661925 But yes it...

    Oct 16, 2017 at 9:50 PM
  11. ZipTie replied to the thread New and excited.

    Hello lightseeker and welcome from Minnesota as I'm stuck here also. Lol You can't go wrong with anything really. Ups and downs from...

    Oct 16, 2017 at 9:45 PM
  12. curtisfox replied to the thread briggs & Stratton 3hp 80300 MODEL HELP..

    Help some 24" would be even better.if you get a torque converter it would give you some reduction. Then change the sprocket to pulley,...

    Oct 16, 2017 at 9:41 PM
  13. el Diablo Guapo posted a new thread.

    Rear sprocket, rag joint, broken spokes and destroyed hub

    MB running great, pulling hard. Fired it up after work, felt an odd "clunking" noticed my rear wheel was not aligned. Pulled out a...

    2017-10-16 18.56.16.jpg

    Forum: Hubs, Gearboxes, Sprockets and Chains

    Oct 16, 2017 at 9:38 PM
  14. truckd replied to the thread 1911 Flying Merkel single build..

    Hey Velodrome can you PM me I have a question for you.

    Oct 16, 2017 at 9:37 PM
  15. nam70 liked corgi1's post in the thread 66cc Chinese motor Electric start?.

    If you are going to do all that ,Why not one of the pocket bike motors you mentioned,more reliable and ready to start

    Oct 16, 2017 at 9:18 PM
Loading...