Search results

  1. Memy1251

    Won’t idle:

    thanks a load, dude! I’m gonna do both those things. Say you don’t layer on the Teflon tape? You just put one little layer?
  2. Memy1251

    Won’t idle:

    Thanks for your help. I figured that could have been a potential cause, but where do you usually see these sorts of leaks if you don’t mind me asking?
  3. Memy1251

    Parts vibrating loose

    L Loctite is also a good idea, I’ll use that!
  4. Memy1251

    Parts vibrating loose

    I’m gonna try the inner tube as that is available to me. Thank you!!
  5. Memy1251

    Won’t idle:

    hey guys, so my first build i ran it and the engine idled flawlessly. For a while, then the bike would no longer idle. When I pull the clutch the RPMS shoot sky high. When I leave the clutch it’s always trying to go like a car placed in “drive”. Any ideas? Thanks guys!
  6. Memy1251

    Parts vibrating loose

    HEY GUYS! Just built my first beauty. It’s running well and strong aside from when I picked up a nail. However I have a question about how you guys like to secure your gas tank and mufflers. My attached components are tending to vibrate loose. Am I just going too fast? Or if there another way to...
  7. Memy1251

    Drive sprocket won’t turn

    H ey!! I actually got it running! It turned out to be a bad magneto this I wasn’t getting any spark. Now however I’m seeing components such as the gas tank and muffler vibrating loose. Any suggestions to secure them down?
  8. Memy1251

    Drive sprocket won’t turn

    Like I mean the brass clamp that hold the carburetor on is set by a pin that holds it in its place. ‍♂️
  9. Memy1251

    Drive sprocket won’t turn

    Im not sure where this ramp that needs to be to the idle screw is. :(
  10. Image

    Image

    Carb/ throttle connection
  11. Memy1251

    Drive sprocket won’t turn

    Okay! I will do! I’ll let ya know in The morning! thanks!
  12. Memy1251

    Drive sprocket won’t turn

    The gas cap was not closed properly and I’ve fix that but sadly the issue still stands. :(
  13. Memy1251

    Drive sprocket won’t turn

    You’re talking about the gas tank cap? Just need to verify. XD that may be it!
  14. Memy1251

    Drive sprocket won’t turn

    Like the en like The engine will turn over when I drop the clutch but as the bike slows down it just dies out. :/
  15. Memy1251

    Noob new gas kit built up... Starting?

    Hey there, I’m having the same problem as Dirty Patches, only my carb is at the right angle. I was wondering if you can’t give me a little advice?
  16. Memy1251

    can't find an answer then ask here someone may be able to help!!

    Norman: I’ve just built my first bike, and it starts and runs but slowly dies. The throttle works but doesn’t push the bike and, it just kicks up the RPMS a bit. Even that gets weaker as the bike dies down. Any suggestions? I ride the choke closed when I start it then when the engine starts I...
  17. Memy1251

    Drive sprocket won’t turn

    Hey it all worked! Now it starts but when I start it it slowly dies away. If I give it throttle it works too but that dies down as well. :/ can ya help me figure what might be killing it?
  18. Memy1251

    Drive sprocket won’t turn

    And it worked!! But now I see that the drive sprocket May have some rough edges. I think the chain is trying to buckle over unless I roll very slow. :/ i don’t have Tools to remove the drive sprocket. Any ideas of how to fix this Macgyver Style?
  19. Memy1251

    Drive sprocket won’t turn

    I have done that process once before, but I will try it holding the clutch bar instead of the clutch handle. Thanks!