Recent content by Mighty_Max

  1. M

    Drowning Carburetor?

    How could it have gotten junk in it? I only just put it on a week ago and its been doing this since my first ride with it. I will try that starting fluid trick and see what happens. I was told that NT carbs were pretty bad for leaking air on the manifold side of things.
  2. M

    My motor tops out at 30km/h, how do I fix this??

    I will agree with 2door on this one based on experience. If you cant figure out how to clean the exhaust out, just buy another one though. They are cheap enough, and while your at it, you could go get a slightly better performing one too. There is a lot of information on the forum about people...
  3. M

    Drowning Carburetor?

    I recently switched from a CNS carb to an NT carb and although my overall performance has improved greatly, i still have a few issues. New ones. Firstly, when i first start up the bike and let it idle, all seams well, it idles at the right speed, and aside from a few missed power strokes, it...
  4. M

    Stripped post

    I was being stubborn and lazy when i posted before. A couple months ago, during the cold snowy month of February, I caved in and bought a helicoil kit from Napa auto parts (the only place I know of that carries them in this size) and it worked beautifully, and it was pretty painless. As for my...
  5. M

    Centrifugal Clutch Acquisition!

    As of 4 minutes ago, i have purchased a centrifugal clutch, pull start, and clutch puller! Thank you Davezilla for your post, it has litterally solved all of my bike problems. This is pretty much the last phase of my bike build where i add aftermarket stuff to see what happens. So far, i have a...
  6. M

    Centrifugal Clutch Acquisition!

    It would be for the 66cc skyhawk gt-5.
  7. M

    Centrifugal Clutch Acquisition!

    I have looked almost everywhere to find a centrifugal clutch kit for sale on the internet and while several sites have them posted for sale, all of them are out of stock. Can anyone help me hunt one down?
  8. M

    Exploding chains

    After i get a new chain, preferably not made by Bell, i will pay more attention to the derailleur. The wheal does seam to be in proper alignment.
  9. M

    Exploding chains

    Yes, as stated in the bottom of my post, its a Sickbikeparts HD shiftkit.
  10. M

    Exploding chains

    Ive assembled a wonderful motorized bike and managed to figure out pretty much everything to make it work, with a little help from the forum. It runs great and it goes pretty well too, however I've only put 11 miles (as stated by speedo) on it and I've killed two chains already. The first break...
  11. M

    Stripped post

    Ok. i can give it a a little while till i freak out too much. Gotta take things slowly.
  12. M

    Stripped post

    I think I might have a tap and die set in storage somewhere. Ive sort of been putting of doing anything to the exhaust because i knew i was going to get an expansion chamber, unfortunately, there wont be a cushion in my wallet for a few weeks yet. When i do get the chamber I'm gonna have to do a...
  13. M

    Stripped post

    Thats a bit expensive and difficult, but thank you for the suggestion.
  14. M

    DAX compatibility

    Is the DAX F80 69cc compatibile with other china girl parts or will parts designed for the chinese engines work with the F80? Specifically, the Sickbikeparts shift kit.Thinking about getting the Engine by itself and slapping the rest of my Grubee parts on there instead.
  15. M

    Stripped post

    I have been somewhat concerned with my engine for a little bit. It keeps 4-stroking and i'm losing out on some power that i feel should be there. I have the SBP shiftkit and in first gear it only goes about 21 mph. In fitfh gear it only goes about 26 and at 7th gear i actually lose speed because...