FOG's Recent Activity

  1. FOG liked Ralph hop's post in the thread Misfit Board Tracker.

    After trimming, fitting, filing and sanding on this fork tube I know there is plenty material for a good weld. For those that have these...

    Apr 2, 2020 at 6:36 PM
  2. FOG attached a file to the thread 49cc's on a Schwinn.

    I found an online calculator for the volume of a dome which led to this ... [ATTACH] All that stuff on the right side is for the wee...

    40mmCylHead.jpg DSCF0943.JPG Apr 2, 2020 at 11:05 AM
  3. FOG liked PeteMcP's post in the thread Hi from the UK - INDIAN Board Tracker tribute, my first build.

    Received Pedal Chopper's cnc'd alloy rear caliper mount in today's mail.Thankfully no customs charges to pay. Very nicely made part -...

    Apr 2, 2020 at 10:39 AM
  4. FOG liked kelly dean's post in the thread HP carb tuning question.

    the NT is a much better carb.. i used the clone awhile just because i had it and have since went to a NT on that bike. glad it's worked...

    Apr 2, 2020 at 10:36 AM
  5. FOG liked Johnny trigger's post in the thread HP carb tuning question.

    I put original manifold and original carb with .68 jet. Sealed everything up good.20-1 gas with yamaha 2 stroke oil.(still newer...

    Apr 2, 2020 at 10:36 AM
  6. FOG replied to the thread 49cc's on a Schwinn.

    As usual I'm goin' off the deep end again by making my own cylinder head. I dunno why. Because I can I guess ... :) Compression ratio...

    Apr 1, 2020 at 2:04 PM
  7. FOG liked indian22's post in the thread Misfit Board Tracker.

    I also tap the axle for end bolts on jack shaft setups and set screws do some damage. Good tips. Rick C.

    Apr 1, 2020 at 9:26 AM
  8. FOG liked kelly dean's post in the thread HP carb tuning question.

    you might try getting it to seal with an O ring. I generally use a 5/8 O ring in a 19mm carb... kelly

    Apr 1, 2020 at 9:23 AM
  9. FOG liked kelly dean's post in the thread requests from friends to buy a budget bike build.

    havent posted in awhile it's up and down health wise but busy when i feel well. several people wanting a low priced bike so i have built...

    20200215_130335.jpg 20200317_210805.jpg 20200317_211118.jpg 20200329_092611.jpg 20200329_092631.jpg 20200329_092800.jpg Mar 31, 2020 at 10:44 AM
  10. FOG liked kelly dean's post in the thread HP carb tuning question.

    If fuel can leak from that connection then air certainly will and thats a very bad situation, and you should address that issue first...

    hp carb.jpg Mar 31, 2020 at 10:13 AM
  11. FOG liked Tyler6357's post in the thread Reaching 50mph on 66/80cc.

    Well, when I first built my bike the idea was to put a shift kit on it. I had planned to get it built and then put the shift kit on it...

    Mar 30, 2020 at 11:07 AM
  12. FOG liked PeteMcP's post in the thread Trek 3700.

    Welcome! MB forum has an enormous reserve of postings/photos from builders prepared to share their experience. With 99% of the...

    Mar 30, 2020 at 11:03 AM
  13. FOG liked PeteMcP's post in the thread Hi from the UK - INDIAN Board Tracker tribute, my first build.

    "...Here's one I made earlier..." as they say. Been playing around with some cardboard mock-ups to get an idea of how I plan to house...

    DSCN3687.JPG DSCN3689.JPG Mar 30, 2020 at 11:01 AM
  14. FOG liked indian22's post in the thread Old Guys Simplex moto-peddle bike.

    Tony gave me a good piece of advice on the battery pack and my tech guy backed him up so I'm doing a battery swap with my builder and...

    Mar 30, 2020 at 10:58 AM
  15. FOG liked TeddyD80's post in the thread First build.

    After more than a month of starting this little project and leaping thru hurdles and set backs, it's finally finished. If I knew then...

    20200329_155834_HDR.jpg Mar 30, 2020 at 10:44 AM