Need muffler exhaust gasket

ezrider

Member

May 18, 2016

121

2

16

Indiana

Mar 23, 2017

• #1

The muffler gasket I'm looking for is for the 66/80 CC single stroke 'China Girl' type engines. Apparently, some vendor's description of the item sez it has a stud spacing of 30 MM = 1.1811 inch which obviously is wrong since it is way to narrow. Anyway, have NO luck putting in an order on either Spooky Tooth Cycles or Bikeberry websites. So consequently, am requesting additional list of vendors that carry this crucial part.

Thanks.

_

 

Chaz

Well-Known Member

Jun 3, 2012

1,004

72

48

Vancouver, British Columbia

Mar 23, 2017

• #2

Here is a link for a gasket. It is designed for two stroke engines but will likely fit your single stroke china girl. Good idea to call the vendor to double check.

http://sickbikeparts.com/exhaust-gasket/

 

Kioshk

Active Member

Oct 21, 2012

1,152

10

38

Connecticut

Mar 23, 2017

• #3

I used this stuff once to make my own. You'll need a tin-snip and a drill/awl.

 

crassius

Well-Known Member

Sep 30, 2012

4,032

158

63

USA

Mar 23, 2017

• #4

I usually order these:
http://www.ebay.com/itm/49cc-66cc-8...Quality-Gas-Bike-Muffler-Gasket-/181952112700

I use a lot of them.

 

Tyler6357

Well-Known Member

Mar 15, 2012

1,293

294

83

Santa Barbara, CA

Mar 23, 2017

• #5

Here are some port matched exhaust gaskets:

http://www.ebay.com/itm/2-PACK-Moto...051225?hash=item35f8a86159:g:OCEAAOSwGtRXx4Fh

http://www.ebay.com/itm/2-PACK-Moto...137896?hash=item4b0f4b4368:g:oWUAAOSwUKxYbFl8

 

ezrider

Member

May 18, 2016

121

2

16

Indiana

Mar 24, 2017

• #6

Chaz said:

Here is a link for a gasket. It is designed for two stroke engines but will likely fit your single stroke china girl. Good idea to call the vendor to double check.

http://sickbikeparts.com/exhaust-gasket/

Click to expand...

Interesting alum material...can be machined. Too bad it doesn't show the exact spec sizes on it.

_

 

ezrider

Member

May 18, 2016

121

2

16

Indiana

Mar 24, 2017

• #7

Kioshk said:

I used this stuff once to make my own. You'll need a tin-snip and a drill/awl.

Click to expand...

For the time being, I get by with the Permatex Ultra Copper gasket maker...but its never intended as a permanent fix.


_

 

Chaz

Well-Known Member

Jun 3, 2012

1,004

72

48

Vancouver, British Columbia

Mar 25, 2017

• #8

ezrider said:

Interesting alum material...can be machined. Too bad it doesn't show the exact spec sizes on it.

_

Click to expand...

That's why I suggested you call first.

 

ezrider

Member

May 18, 2016

121

2

16

Indiana

May 21, 2017

• #9

Here's an update on my gasket situation:

Received the 'heavy duty' muffler flange gasket from Bikeberry. Problem was, it was only smooth and flush on one side only, and really rough on the other side. Consequently, the bike ride was much louder. Resolved this issue, by applying a thin coat of Permatex on the muffler pipe flange facing the rough side gasket. Couldn't be happier.

Thanks for all the replies.

_